Skip to main content
Agent skill

Cisco Ios Patterns

Cisco IOS and IOS-XE review patterns for show commands, config hierarchy, wildcard masks, ACL placement, interface hygiene, and safe change-window verification. Use when reading, writing, or reviewing Cisco IOS / IOS-XE configuration or planning a change window.

Get started

Get the complete skill folder, including its scripts and reference files.

·

When to use this skill

Use Cisco Ios Patterns when an AI agent needs a reusable SKILL.md workflow for this job: Cisco IOS and IOS-XE review patterns for show commands, config hierarchy, wildcard masks, ACL placement, interface hygiene, and safe change-window verification. Use when reading, writing, or reviewing Cisco IOS / IOS-XE configuration or planning a change window.

When not to use it

Skip Cisco Ios Patterns when the task is outside the writing category, or when a more specific skill in this directory already covers the same workflow with clearer triggers.

How to install

Where will you use it?

Install scope
Claude Code folder setup
mkdir -p ~/.claude/skills/cisco-ios-patterns
# Save SKILL.md to ~/.claude/skills/cisco-ios-patterns/SKILL.md
  1. Claude Code personal install: place the skill and its bundled files at ~/.claude/skills/cisco-ios-patterns/SKILL.md. For a shared project, commit the folder at .claude/skills/cisco-ios-patterns/ instead.
  2. Current Claude Code detects SKILL.md changes in watched directories during the session. If you just created a top-level skills directory, run /reload-skills. Check that the skill is listed before testing its trigger.
  3. For Claude chat or Cowork in the Desktop app, manage uploaded skills in Customize > Skills; copying files into a local Claude Code folder is not a Desktop install. Other agents may use different install locations.

Full install guide for Claude, Cursor, and Codex →

Try a starter prompt

After installing the skill, paste this starter prompt into your agent to verify it triggers on a small task.

Starter prompt
Use the Cisco Ios Patterns skill for this task: Reviewing IOS or IOS-XE configuration before a planned change. Confirm any required inputs or files before making changes.

What supports this recommendation?

83/100 provisional content score. This measures documentation, practical detail and source signals. It is not a measured task success rate or a security certification.

Documentation
92/100
Practical detail
92/100
Source evidence
63/100
Source signals
72/100
Model compatibility evidence
  • claudeuntested

    No model-specific signal or recorded compatibility test was found.

  • chatgptuntested

    No model-specific signal or recorded compatibility test was found.

  • geminiuntested

    No model-specific signal or recorded compatibility test was found.

  • copilotuntested

    No model-specific signal or recorded compatibility test was found.

  • llamauntested

    No model-specific signal or recorded compatibility test was found.

  • perplexityuntested

    No model-specific signal or recorded compatibility test was found.

  • mistraluntested

    No model-specific signal or recorded compatibility test was found.

  • grokuntested

    No model-specific signal or recorded compatibility test was found.

Inferred compatibility is based on content signals. Check the app, its available tools and setup requirements before running a skill.

What this skill does

# Cisco IOS Patterns

Use this skill when reviewing Cisco IOS or IOS-XE snippets, building a change-window checklist, or explaining how to collect evidence from a router or switch without making the incident worse.

## When to Use

- Reviewing IOS or IOS-XE configuration before a planned change. - Choosing read-only `show` commands for troubleshooting. - Checking ACL wildcard masks and interface direction. - Explaining global, interface, routing process, and line configuration modes. - Verifying that a change landed in running config and was saved intentionally.

## Operating Rules

Treat IOS examples as patterns, not paste-ready production changes. Confirm the platform, interface names, current config, rollback path, and out-of-band access before making changes on a real device.

Prefer this workflow:

1. Capture current state with read-only commands. 2. Review the exact candidate config. 3. Confirm management access cannot be locked out. 4. Apply the smallest change in a maintenance window. 5. Re-read state, compare to the baseline, then save only after validation.

## Mode Reference

```text Router> enable Router# show running-config Router# configure terminal Router(config)# interface GigabitEthernet0/1 Router(config-if)# description UPLINK-TO-CORE Router(config-if)# no shutdown Router(config-if)# exit Router(config)# end Router# show running-config interface GigabitEthernet0/1 ```

`running-config` is active memory. `startup-config` is what survives reload. Do not save a change just because a command was accepted; validate behavior first, then use `copy running-config startup-config` if the change is approved.

## Read-Only Collection

```text show version show inventory show processes cpu sorted show memory statistics show logging show running-config | section line vty show running-config | section interface show running-config | section router bgp show ip interface brief show interfaces show interfaces status show vlan brief show mac address-table show spanning-tree show ip route show ip protocols show ip access-lists show route-map show ip prefix-list ```

Collect the specific section you need instead of dumping full config into a ticket when the config may contain secrets, customer names, or private topology.

## Wildcard Masks

IOS ACL and many routing statements use wildcard masks, not subnet masks.

```text Subnet mask Wildcard mask 255.255.255.255 0.0.0.0 255.255.255.252 0.0.0.3 255.255.255.0 0.0.0.255 255.255.0.0 0.0.255.255 ```

Review wildcard masks before deployment. A subnet mask accidentally used as a wildcard can match far more traffic than intended.

```text ip access-list extended WEB-IN 10 permit tcp 192.0.2.0 0.0.0.255 any eq 443 999 deny ip any any log ```

Every ACL has an implicit deny at the end. Add an explicit logged deny when the operational goal includes observing misses, and confirm logging volume is safe.

## ACL Placement Review

Before applying an ACL to an interface, answer these questions:

- Which traffic direction is being filtered, `in` or `out`? - Is management traffic sourced from a known jump host or management subnet? - Is there an explicit permit for required routing, DNS, NTP, monitoring, or application traffic? - Are hit counters available from a safe test source? - Is there a rollback command and an active console or out-of-band path?

Do not test reachability by removing firewall or ACL protections. Read counters, logs, and route state first.

## Interface Hygiene

```text interface GigabitEthernet0/1 description UPLINK-TO-CORE switchport mode trunk switchport trunk allowed vlan 10,20,30 switchport trunk native vlan 999 no shutdown ```

Use clear descriptions, explicit switchport mode, and documented native VLANs. On routed interfaces, confirm the mask, peer addressing, and routing process before assuming link state means forwarding is correct.

## Change-Window Verification

Use before/after checks that match the actual change.

```text show running-config | section interface GigabitEthernet0/1 show interfaces GigabitEthernet0/1 show logging | include GigabitEthernet0/1|changed state|line protocol show ip route <prefix> show ip access-lists <name> ```

For routing changes, also capture neighbor state and route tables before and after the change. For ACL changes, compare hit counters from a planned test source rather than relying on a generic ping.

## Anti-Patterns

- Applying a generated config without a device-specific diff. - Saving configuration before post-change checks pass. - Using a subnet mask where IOS expects a wildcard mask. - Applying an ACL to the wrong interface direction. - Troubleshooting by disabling ACLs, route policies, or authentication. - Pasting full configs into public tools without sanitizing secrets and topology.

## See Also

- Agent: `network-config-reviewer` - Agent: `network-troubleshooter` - Skill: `network-config-validation` - Skill: `network-interface-health`

Intended uses

  • Reviewing IOS or IOS-XE configuration before a planned change.
  • Choosing read-only show commands for troubleshooting.
  • Checking ACL wildcard masks and interface direction.
  • Explaining global, interface, routing process, and line configuration modes.
  • Verifying that a change landed in running config and was saved intentionally.

Implementation notes

  • Review the source instructions and adapt inputs before running the workflow.

Try it, then tell us how it went

A copied prompt does not tell us whether the task worked. Report your result after checking the output. We collect your tool and outcome, never your files or prompt.